Society of Professional Rope Access Technicians (SPRAT) Level 1 Practice Test

These questions are part of the practice quiz. Start practicing

• Which item is included in the Review of Job Safety Analysis?
• __________ have the responsibility to document the work experience and training of the rope access technicians in their work team
• Which sequence correctly describes the basic steps of a simple self-rescue with a descender?
• A SPRAT Level 1 Technician may perform rope access work under the supervision of which levels?
• During an ascent, which action best supports safe rope management?
• During a pre-use inspection, which of the following is an example of contamination to look for?
• What is the role of a rigging plan before starting work?
• The area in which people are at risk of falling such as rope access technicians on-rope or near a working edge is defined as a
• In rope systems, what best describes 'shock loading'?
• What is the recommended process for cleaning and drying after use?
• What is the benefit of belaying from above if possible?
• What is a Prusik knot used for in rope access?
• Hazard Zone is defined as which statement?
• Name a commonly used stopper knot.
• What is the primary objective of a risk assessment before starting a rope access job?
• What is a simple lowering technique and its importance?
• Which statement describes the Review of the Work Environment?
• The Rescue Plan will include what content?
• The _____ is a written statement prepared by the employer describing how a particular job should be undertaken.
• Which zone is defined as the area where there is a risk of falling?
• Ascenders provide attachment points for device lanyards and other devices.
• The harness used for rope access should be of which type?
• What should you do if you hear a rope slip or hear unusual noises?
• Which device type should allow for controlled descent and braking?
• What action should you take immediately when there is a risk of fallen object impact?
• In a dual main system, how are loads distributed?
• Describe how to set up a basic friction hitch as a backup for control.
• What is a possible consequence of not using edge protection on a rope that passes over a sharp edge?
• How should you communicate a dangerous situation to your team?
• When should a communication plan be established?
• Which term defines the area where a person is at risk of falling?
• Lanyards in SPRAT rope access must:
• What is the purpose of labeling a rope as out of service?
• Which document describes how a particular job should be undertaken?
• The Review of the Work Environment will address which topics?
• When is a changeover of rope or equipment recommended?
• What is the breaking strength for harness attachment points?
• What is kernmantle rope?
• What is the recommended practice for the backup device to limit free fall potential?
• What is the purpose of a backup knot in rope access?
• What is a two-rope system used for in SPRAT?
• If you are unsure about a rigging configuration, what sequence should you follow?
• Which term best describes areas where there is a potential for injury due to ongoing work, including items like falling tools or moving gear?
• What is a defining feature of ascenders in rope access?
• What is the difference between static and dynamic rope in rope access, and which is typically recommended for SPRAT Level 1 work?
• What is the role of edge protection in high-angle work?
• What is the correct action if you feel a fall arrest device overheats?
• Which statement best describes a tie-in?
• Which two factors define acceptable anchor redundancy?
• What is the minimum number of anchors required for main and backup systems?
• In a rope access operation, what is the proper term for the hazard area where dropped objects may pose a risk?
• Which statement about anchor redundancy best describes proper practice?
• Which factor is essential to check to prevent rope damage when guiding ascent near edges?
• Which statement describes when supervisor involvement is appropriate according to SPRAT Level 1 guidelines?
• What is a typical use for a dual main system?
• Which statement about two independent anchors is true?
• What is the purpose of the Rescue Plan?
• What is the maximum horizontal separation between independent main rope systems in a dual main system?
• Which option is NOT an appropriate step when documenting defects or incidents?
• What is a proper action when documenting equipment defects or incidents?
• Which role is responsible for the overall safety and coordination of rope access operations at a worksite?
• Why is proper edge protection important during rope movement?
• Pre-cert requirements include:
• Which sequence represents the typical steps for a basic SPRAT Level 1 ascent?
• The use of a directional anchorage system to deflect a two-rope system from the fall line is called what?
• What does the term 'load path' refer to in rope access?
• Provision for prompt rescue is a ________ of the rope access program.
• During pre-use checks of a descent device, which factor is essential for safe operation?
• The log book for rope access work typically includes:
• Which of the following is NOT a sign of rope core damage?
• Why should tie-in points be accessible and connected to the rope system per SOP?
• If you are unsure about a rigging configuration, what sequence should you follow?
• Which device used for rope access is designed to prevent detachment from the rope during normal use?
• How should weather exposure be managed to protect rope and equipment?
• How should rope be cleaned and dried after use to prolong life?
• Which item is NOT considered mandatory PPE for SPRAT Level 1 operations?
• Which application describes a dual main system's typical use in rope access operations?
• Name two common knots used to tie into a rope for SPRAT tasks?
• Hazard Zone is defined as which?
• Which of the following is a measure to prevent rope wear at edges?
• Sharp or abrasive surfaces on a work site are hazardous because they may
• The requirement for a separate rope system for heavy equipment serves to ensure the heavy tools do not interfere with the main rope system.
• Which factor is NOT listed among rope selection considerations?
• What is the standard method to transport rope to a job site?
• Equipment used for rope access ______ be compatible with other components of the system.
• Which statement best describes edge protection's effect on rope use?
• What is the purpose of a rescue plan in rope access?
• What is the role of a sit or chest harness in SPRAT Level 1 practice?
• Which statement best describes when you should involve a supervisor?
• Limited Free Fall Potential is defined as the restriction of possible free fall to no greater than which distance?
• What is the purpose of a pre-job briefing with the team?
• The attachment point on the harness the rope access backup system typically connects to is the
• MBS stands for:
• Anchorage Systems guidelines specify a two rope system consisting of a main and backup rope should have an MBS of what, or two times the maximum arrest force of the backup system, whichever is greater?
• Which term describes the object that bears the load of a rope access system?
• Which practice helps maintain controlled rope management during operation?
• Fall Line refers to which of the following in rope access terminology?
• Which term refers to using a directional anchor to move a two-rope setup away from the fall line?
• When should a supervisor be involved in the rope access operation?
• What is a 'working line' in rope access terminology?
• Rope behavior for SPRAT ropes is typically:
• The _________ is a separately anchored rope used within a backup system to protect against falls if the user slips or a component of the main system fails.
• Which action best reduces the risk of rope abrasion at edges?
• What is the term for any area where a person may be at risk due to work, such as dropped tools?
• Carabiners are designed to be loaded along the
• Which statement about SPRAT ropes is true?
• The ___ is the entire system, including anchorage system(s), rope(s), and/or equipment required to support the expected forces of a rope access technician or a load during normal use.
• Which storage practice supports rope longevity after a long job?
• Who is described as the person responsible for the entire rope access work site, including management of other technicians?
• What is a common method to manage rope slack during movement?
• When observing changing weather conditions, what should you do?
• How should you ensure proper body positioning while working on a rope?
• How should you verify a job’s permit-to-work status?
• Which statement best describes a two-rope anchorage system?
• Which statement best describes SPRAT's requirement for equipment considered good?
• Which components are included in the main system?
• Which knot is used to create a friction hitch for ascending in rope access?
• Which is a key element of a buddy check before starting work?
• If equipment shows damage in the field, what is the standard practice?
• What is edge protection and why is it important in rope-access work?
• What are the basic signs of rope core damage?
• How should a full-body harness be worn and secured before rope work?
• Why is a tidy and organized workspace important in rope access?
• Which of the following is NOT a responsibility of a rope access technician?
• How should communication be established on a rope-access job?
• What is the purpose of a control line in a belay system?
• When choosing rope diameter, which factor is essential?
• When is it appropriate to wear gloves in rope access?
• Which role would typically oversee the safety program and ensure compliance with procedures across the rope access operation?
• Which factor is not listed as part of evaluating environmental conditions for safe work?
• In rope access, the backup rope is used to protect against falls if the main system fails.
• Which items are contained in the Work Method?
• What is the purpose of a buddy check before starting work?
• Which topic is included in a basic SPRAT Level 1 toolbox talk?
• What is the recommended practice for rope care after a long job?
• How would you explain the principle of “load sharing” in a two-anchor system?
• During a rope access operation, which role should oversee overall safety practices and coordinate emergency procedures?
• What is the typical length guideline for lanyards to minimize fall potential?
• What should the Review of Job Safety Analysis include?
• Fall Zone is defined as which?
• Which correctly lists the four types of inspection?
• Which position is described as the person with the training, skills, experience, and certifications necessary to assume responsibility for the entire rope access work site?
• What are the four components that make up an Access Work Plan?
• __________ used for rope access shall be designed to prevent inadvertently detachment or removal from the rope under normal use
• How should you document any equipment defects or incidents?
• What is the term for the area where hazards exist due to ongoing work, such as loose tools or moving gear?
• What is the equivalent of 12 kN in pounds-force (lbf)?
• For a two-rope anchorage system, which statement correctly summarizes the minimum MBS requirement?
• Which outcome is not directly affected by maintaining a clean work area?
• A ______ rope consists of an internal load bearing core enclosed within a separate sheath.
• Low stretch rope is characterized by elongation of what percentage at 10% of its minimum breaking strength?
• Only ______ carabiners are suitable to use in rope access systems supporting human loads.
• Who is responsible for documenting the work experience and training in a rope access team?
• Descenders must satisfy which capabilities?
• Which factor is most important when selecting rope diameter?
• What is the function of a damping device in rope systems?
• What is the minimum number of people required to work as a team in SPRAT rope access?
• What factors should be considered when selecting a rope for a job?
• ___________ shall allow for controlled descent and braking.
• Rope Access harness used for rope access shall be of the
• Which action should you take if environmental conditions become unsafe during a rope access operation?
• What should you check when you inspect a descent device?
• Which statement best describes the purpose of a sit or chest harness?
• During rope access operations, which role is primarily responsible for planning rescue procedures and ensuring equipment readiness on a job site?
• What does the Job Safety Analysis involve?
• What term describes the person who has the training, skills, experience and certifications necessary to assume responsibility for the entire rope access work site, including management of other rope access technicians?
• In rope access, the technique of using a directional anchor to move a two-rope system away from the fall line is known as what?
• Which items are considered mandatory PPE for SPRAT Level 1 operations?
• What does 'tie-in' mean in SPRAT rope access?
• Ropes used in a rope access for main and back up systems should be
• Who should you consult if you are unsure about rigging?
• What is a basic method to verify rope length and usage during ascent?
• What should edge protection help prevent?
• What is the purpose of a two-person communication protocol during rope access?
• Which statement correctly summarizes the minimum MBS guidance for a two-rope anchorage system?
• Tools or equipment weighing more than ______ should be suspended with separate rope system.
• Why is it important to maintain a clean work area on a rope access job?
• Which forms of communication are included and reviewed by all members of the work team?
• What is the maximum interior angle from the load to the anchorage systems in a dual main system?
• Backup systems are implemented to achieve which of the following outcomes?
• What is the purpose of edge guards or rub-strips at anchor points?
• What are the two harness attachment points called?
• The minimum strength of a directional anchorage system is determined by which factor?
• What should you inspect on a rope before use?
• What constitutes a compliant anchor line for SPRAT Level 1?
• What is a key outcome of a well-designed load path through anchors?
• What is essential to ensure a proper tie-in with the harness?
• What should you do if there is a fallen object risk on a rope access site?
• Ropes are made from which materials?
• What is the function of a watch/runner in rope systems?
• What is the minimum breaking strength for connectors (MBS)?
• Which position is responsible for supervising the entire rope access work site and coordinating other technicians?
• Describe the role of a friction hitch backup in control?
• The ______ is any area outside the hazard zone or the fall zone.
• Which of the following is true about the communication plan during active work?
• What is a typical indicator of equipment fatigue in a rope access system?
• How do you prevent kinking or twisting of rope during operation?
• Which practice supports safe operation when weather changes occur?
• When selecting rope diameter, which outcome is the primary consideration?
• When is dynamic testing appropriate?
• What is the difference between a tether and a lanyard in rope access?
• How should you store rope to prevent damage?
• In a restraint or lowering scenario, how should you handle a casualty with suspected spinal injury?
• What is the purpose of a pre-use rope and equipment inspection?
• How should you manage heat and fatigue during rope access work?
• In the Review of Job Safety Analysis, which item assesses whether security to anchorage location is necessary?
• Equipment inspection should be conducted from purchase to retirement.
• Explain why redundancy in anchor points is critical in SPRAT Level 1.
• What is the purpose of a rescue plan?
• Which practice best supports maintaining a controlled environment during a rope operation in the field?
• Tools and equipment heavier than 22 lbs in mass should be suspended with a ______ rope system secured to an independent anchorage system.
• How do you determine if an anchor system is properly redundant?
• Describe the basic function of a belay device in SPRAT rope access.
• What is the main purpose of edge protection in high-angle work?
• What is the correct procedural action when defects are found?
• What should you do if you notice a suspected damaged rope during inspection?
• Why is it important to avoid dynamic testing of equipment in normal work routines?
• What is the primary reason to store rope away from moisture after use?
• Special Permits shall be determined by the work being conducted and include which items?
• Ascenders are easily adjustable when moving up and down the main rope. true or false?
• Fall Zone Extends a minimum Distance is how many meters?